Do you have a Mustang that you use only for racing? Then why don't you get rid of the air pump? They're not needed on racing vehicles, and you will reduce the front-end weight, too. These Ford Racing smog pump eliminator bracket idlers are direct bolt-on...

These Ford Racing V-Belt Horsepower pulley kits increase horsepower by reducing accessory drive belt speed. Each 3-piece kit consists of crankshaft, water pump, and alternator pulleys. These pulleys are machined from cast aluminum.

These Ford Racing air conditioning eliminator kits are just the ticket for taking off unwanted front-end weight. Lightening the front of your vehicle improves rear weight transfer and reduces ETs, and it's never been easier to do than with these...

Install a set of BBK performance underdrive pulleys and see an average of 8-15 additional horsepower over the stock pulleys. Under drive pulleys increase engine output by reducing the draw of the engines accessories by slowing them down and reducing the...

Install a set of BBK performance underdrive pulleys and see an average of 8-15 additional horsepower over the stock pulleys. Under drive pulleys increase engine output by reducing the draw of the engines accessories by slowing them down and reducing the...

Install a set of BBK performance underdrive pulleys and see an average of 8-15 additional horsepower over the stock pulleys. Under drive pulleys increase engine output by reducing the draw of the engines accessories by slowing them down and reducing the...

Install a set of BBK performance underdrive pulleys and see an average of 8-15 additional horsepower over the stock pulleys. Under drive pulleys increase engine output by reducing the draw of the engines accessories by slowing them down and reducing the...

Install a set of BBK performance underdrive pulleys and see an average of 8-15 additional horsepower over the stock pulleys. Under drive pulleys increase engine output by reducing the draw of the engines accessories by slowing them down and reducing the...

VMP-SUT014. Combo tensioner 17mm length hex nut VMP-SUT017. VMP 60mm alum idler pulley 1.5"DR VMP-60-SM-DB. Idler standoff VMP-ISPC-7-17-SM. VMP 76mm ribbed idler - 10-rib VMP-76-10-20-RB. VMP-TSPC-20-8-10RB and VMP-SPC-155-8-10RB.

VMP-SUT014. Combo tensioner 17mm length hex nut VMP-SUT017. VMP 60 mm alum idler pulley 1.5"DR VMP-60-SM-DB. Idler standoff VMP-ISPC-7-17-SM. VMP 76mm ribbed idler - 10-rib VMP-76-10-20-RB. VMP-TSPC-20-8-10RB and VMP-SPC-155-8-10RB.

VMP-SUT014. Combo tensioner 17 mm hex nut VMP-SUT017. VMP 60mm alum idler pulley 1.5"DR VMP-60-SM-DB. Idler standoff VMP-ISPC-7-17-SM. VMP 76mm ribbed idler - 6-rib VMP-76-6-20-RB. VMP-TSPC-20-6RB and VMP-SPC-12-6RB.

VMP No-Grind FEAD Kit for TVS Supercharged '11+ Coyote (Race/Heavy-Duty Version) This kit is designed to work with older VMP and Roush blower kits with the 2.3 L or 2.65 L supercharger. It replaces the cast Roush FEAD bracket and spider bracket that...

VMP No-Grind FEAD Kit for TVS Supercharged '11+ Coyote (Street Version) This kit is designed to work with older VMP and Roush blower kits with the 2.3 L or 2.65 L supercharger. It replaces the cast Roush FEAD bracket and spider bracket that require...

VMP 10-Rib Full-FEAD Kit for '11+ Odin Supercharged Coyote w/oAC - 20% OD. For cars with or without ground front timing covers and NO AC. To use this with AC you must purchase the AC pulley separately: VMP '11-17 Mustang & F150 AC Clutch Pulley 10-Rib...

VMP 10-rib Full-FEAD kit for Gen3R Supercharged Coyote AC - 20% OD. This version is for front covers that have not been ground on. Also works with Roush and VMP 2.3 L blowers. If your front cover was previously ground you will need to purchase a "woAC"...

VMP 10-Rib Full-FEAD Kit for '11-17 Gen3R Supercharged Coyote w/o AC - 20% OD For cars with ground front timing covers (Roush style FEAD) or NO AC. This is a full-FEAD kit which completely replace all FEAD components with new parts from VMP. These parts...

Odin 8-rib "Full-FEAD" Kit with AC 10% OD This "Full-FEAD" kit is designed for customers that currently have nothing OR want the latest and greatest belt drive parts. All Odin/Loki belt system components and hardware are included with this kit, perfect...

VMP Atlas Bracket for Odin FEAD system 6/8/10-rib The Odin no-grind FEAD system has continued to evolve with the addition of the Atlas bracket! The Atlas bracket incorporates an adjustable idler pulley to increase belt wrap around the supercharger pulley...

VMP 10 Rib Damper w/ 20% OD for 2020 GT500 and 10 Rib Odin Coyote Product Features: 10-rib version, not recommended for use with 8-rib belts, may jump due to no lip. 20% Overdrive (Diameter 7.91?) Adds approximately 4psi of boost ATI Damper made to...

VMP 10 Rib Damper w/ 10% OD for 2020 GT500 and 10 Rib Odin Coyote Product Features: 10-rib version, not recommended for use with 8-rib belts, may jump due to no lip. 10% Overdrive (Diameter 7.5") Adds approximately 2 psi of boost ATI Damper made to...